Maintenance procedures and precautions for thin-walled bearings
Release time:
2023/01/14
Share:
Do not install it hard on the ball, which will lead to local overload of the ball and contact surface and premature failure of the bearing. Do not use hammer, screwdriver and other hard tools to hit the bearing surface, which will break or embrittle the outer ring of the bearing.
Cleaning of thin-walled bearing and clean environment are very important for bearing. The surface roughness accuracy of the rotating surface and rolling body of the ball bearing ring is about 1/10 m. If the smooth spherical surface is polluted, the impact will be very serious. The lubricating layer between the rolling surfaces is usually 0.2~1 micron, and the granular impurities larger than the lubricant particle size will be excessively crushed by the rolling body, resulting in local compression of the self-aligning roller bearing steel and eventually permanent fatigue of the material. In addition, the size of dust particles in the external environment can reach 10 microns, which will also damage the self-aligning roller bearing. Therefore, a clean and tidy working environment is very important for bearings.
During the process inspection of thin-walled bearing, the working temperature of the bearing is induced by heating. If the temperature exceeds the specified limit, it will automatically alarm to prevent shaft burning. High temperature usually indicates that the bearing is in abnormal condition. High temperature is also harmful to the lubricant of bearing. Sometimes the overheating of the thin-walled deep groove ball bearing can be attributed to the lubricant of the bearing. If the bearing is connected for a long time at a temperature of more than 125, the service life of the bearing will be reduced. The reasons for high bearing temperature include: insufficient bearing lubrication, unqualified impurities in lubricating oil, insufficient bearing internal clearance when the load is too large, causing oil seal friction, etc.
Sealing device
The corresponding sealing devices are installed at both ends of the thin-walled bearing, but many people do not know what role the sealing device plays. Let's see what the sealing device does for thin-walled bearings. Keep the grease inside the bearing from losing during use, and ensure that the bearing is in a lubricating state. Prevent dust or harmful gas outside the bearing from entering the bearing cavity to avoid damage to the bearing.
The sealing structure of thin-walled bearing sealing ring is various, so the sealing effect is also different. If there is a gap between the seal ring and the shaft, it is called non-contact seal. The smaller the clearance, the better the sealing effect, but the smaller the allowable speed of the shaft. On the contrary, on the contrary. If there is no gap between the seal ring and the shaft, it is called contact seal. The larger the contact area of the contact lip of the seal ring, the better the sealing effect, but the smaller the allowable speed of the shaft, the opposite. The main research content of sealing technology is to research and develop corresponding sealing devices suitable for different working conditions, as well as the compatibility of sealing ring material and corresponding lubricating grease.
Related news
2023/01/14
Non-standard bearing condition requirements and technical countermeasures
Not to mention the carbon content, hardness, wear resistance, roughness and consistency of steel balls and ferrules. Regardless of the specific appearance, there are ferrous metal cages, non-metallic cages and non-ferrous metal cages. MC1, MC2, MC3, MC4 and MC5 can be selected according to the fit tolerance; The accuracy of P0, P6, P5 and P4 can be selected according to the purpose; Hundreds of greases can be selected from high temperature to low temperature according to working conditions, and small pictures are attached at will: In this sense, we say that bearings are not standard parts. According to the specific use conditions, I can provide 608 bearings with different performance for your choice. In order to standardize, the parameters of bearings (size, sealing form, retaining frame material, clearance, oil, grease, etc.) should be limited. Conclusion: For non-standard bearings, they cannot be simply regarded as standard parts, but the meaning of non-standard parts should be understood. Then, I will give you a diagram of bearing condition requirements and technical countermeasures. Only by knowing the working conditions of your own products can you choose the right products. Thrust cylindrical roller bearing. It is composed of washer raceway ring (shaft ring, seat ring), cylindrical roller and cage assembly. Bearing type Full-cylinder roller is produced and processed with convex surface. The pressure distribution on the roller and raceway surface is uniform. It can bear one-way axial load, with large axial load capacity and strong axial stiffness. Application field: oil drilling rig, iron and steel machinery. Thrust needle roller bearing. The separated non-standard bearing is composed of raceway ring, needle roller and cage assembly, which can be combined with the stamping of thin raceway ring or cutting of thick raceway ring. Non-release bearing is an integral bearing composed of precision stamping raceway ring, needle roller and cage assembly, which can bear one-way axial load. These bearings take up less space, which is conducive to the compact design of machinery. Most only select the needle roller and cage assembly, while the assembly surface of the shaft and housing is used as the raceway surface. Application field: transmission of automobiles, cultivators, machine tools, etc. Thrust tapered roller bearing. This non-standard bearing is equipped with a round table roller (the big end is spherical), which is accurately guided by the rib of the raceway ring (shaft ring, seat ring). In design, the apex of the cone surface of the shaft ring, race raceway surface and roller rolling surface intersects at a point on the bearing centerline. One-way bearing can bear one-way axial load, and two-way bearing can bear two-way axial load. One-way application: crane hook, oil rig swivel. Two-way: mill roll neck. Turntable bearing. The non-standard bearing of the turntable has high axial and radial bearing capacity, high tilt stiffness and high accuracy, and is suitable for the non-standard bearing configuration in the turntable, measurement and experiment. When installing this bearing, it is necessary to control the torque of the mounting screws. 10、 Rotary table bearing and non-standard customized type. The turntable bearing can bear large radial load, axial load and overturning torque at the same time. It integrates support, rotation, transmission, fixation and other functions. It is compact in structure, simple in installation and convenient in maintenance. It is usually used in low-speed situations such as lifting machinery, excavators, turntables, wind turbines, astronomical telescopes, tank turrets, and is widely used.
Click to view details >
2023/01/14
Non-standard bearings: What are the basic concepts and characteristics of deep groove ball bearings?
Non-standard bearing manufacturers said: with the continuous development of China's heavy industry, some parts commonly used in the construction and engineering fields have also surfaced. Deep groove ball bearing is actually a rolling bearing composed of inner ring, outer ring and other parts. Simple structure, durability, environmental protection, firmness, fast running speed, no need for regular maintenance and cleaning. The utility model has the advantages of convenient operation, small friction coefficient and wide application range. Various types of deep groove ball bearings can be used in different parts of the product. The following are the basic concepts and characteristics of non-standard bearing manufacturers:
Click to view details >
2023/01/14
Maintenance procedures and precautions for thin-walled bearings
Do not install it hard on the ball, which will lead to local overload of the ball and contact surface and premature failure of the bearing. Do not use hammer, screwdriver and other hard tools to hit the bearing surface, which will break or embrittle the outer ring of the bearing.
Click to view details >
2023/01/14
Understand the thin-wall bearing maintenance procedures
The lubrication purpose of thin wall bearings is to reduce the internal friction and wear of bearings and prevent burning and sticking. The lubrication effect is as follows. Reduce friction and wear. The metal contact is prevented and the friction and wear are reduced in the contacting part of the ring, rolling element and retainer of the bearing. Rolling fatigue life that extends the fatigue life. When the rolling contact surface is well lubricated during rotation, the rolling fatigue life will be extended. On the contrary, if the oil viscosity is low and the lubricating oil film thickness is not good, it will be shortened.
Click to view details >We firmly believe that Yisheng can become your best partner!
Yisheng Bearing-Miniature Deep Groove Ball Bearing Product Expert
Xingye North Road, Zhouxiang Town, Cixi City